
Mail-In Diesel Injector Testing: Ship from Anywhere in the U.S.
02/22/2026
John Deere Injection Pump Problems: Symptoms, Causes & Rebuild Options
02/22/2026Updated October 2026: added winter anti-gel picks, what to do about diesel bugs, and the lubricity spec in plain numbers.
Jump to: quick picks by need · the lubricity spec · water and diesel bugs · winter anti-gel
Why Listen to Us About Fuel Additives?
There are hundreds of articles ranking diesel fuel additives. Most of them are written by people who have never seen the inside of an injection pump or pulled carbon off a set of injectors.
We have. Valley Fuel Injection & Turbo is a Bosch, Stanadyne, Delphi, Denso, and Yanmar authorized service center that tests, rebuilds, and calibrates diesel fuel injectors and injection pumps every day. We see what fuel does to injection systems from the inside, the varnish deposits, the scored plungers, the carbon-packed nozzle tips, the corroded check valves. After thousands of teardowns over decades, we have opinions backed by physical evidence.
Talk to a Diesel Tech Additive won’t fix an injector that’s already failing If you are shopping additives because something already changed (rough idle, smoke, hard starts, dropping economy), get it diagnosed first: it may be deposits, or it may be wear that no bottle reverses. Call and tell us what the engine is doing: we will tell you whether it is worth testing the injectors, or whether you are fine to keep running additive and leave it alone. Two ways in: drive it into our Woodland shop near Sacramento, or ship it to us from anywhere in the country. ☎︎ Call 530-668-0818Out of the area? Start a mail-in rebuild → |
We’re also an authorized Stanadyne dealer, we sell Stanadyne Performance Formula and their other additive products. We’ll be upfront about that. We’ll cover the other major brands fairly and tell you what actually matters when choosing a diesel fuel additive.
Diesel Fuel Treatment vs Additive: What Is the Difference?
There is no real difference: “diesel fuel treatment,” “fuel conditioner” and “diesel fuel additive” all mean a product you pour into the tank to change how the fuel performs, and brands use the names interchangeably. What matters is what is in the bottle, so read the label for the jobs it actually does (lubricity, cetane, detergent, water control, anti-gel, stabilizer) and buy for the job your engine needs.
Do Diesel Additives Work?
Yes, for the jobs they are built for, and on different clocks. A cetane improver works on the tank you put it in: the fuel lights sooner, which you notice as easier cold starts and less knock and smoke. Lubricity and detergent additives pay off slowly, as less pump and injector wear and cleaner nozzles over thousands of miles, which is why you run them every tank and not once in a while (Chevron’s Diesel Fuels Technical Review describes the same split).
What no additive does is fix a worn injector or pump, or add 10 to 20 percent fuel economy to a healthy engine. If the engine already smokes, knocks or starts hard, get it diagnosed first: it may be deposits, or it may be wear that no bottle reverses. Get the injectors tested before you spend money on bottles.
Why Diesel Fuel Needs an Additive in the First Place
If you’re running a diesel built before 2007, this is important. If you’re running anything newer, it’s critical.
ULSD Changed Everything
In 2006, the EPA mandated Ultra Low Sulfur Diesel (ULSD), reducing sulfur content from 500 parts per million down to 15 ppm. That was necessary for modern emissions equipment (DPF, SCR, DEF systems) to function. But the refining that removes sulfur also strips out the natural compounds that gave diesel its lubricity. That took away a significant portion of the fuel’s ability to protect the precision surfaces inside injection pumps and injectors.
Modern common rail systems operate at 25,000-30,000+ PSI. The fuel itself is the only lubricant for the internal components of your injectors and high-pressure pump. When that fuel has reduced lubricity, internal wear accelerates, and at those pressures, even microscopic wear changes how the system performs.
Diesel Lubricity Additive: What the Spec Actually Requires
Lubricity is measured with the HFRR test (ASTM D6079). A steel ball is rubbed back and forth on a steel plate in a sample of the fuel, and the size of the wear scar shows how well that fuel protects metal. Smaller is better.
- 520 microns: the largest wear scar the US diesel spec, ASTM D975, allows. California’s CARB diesel uses the same limit (DieselNet summary of US diesel fuel specs).
- 460 microns: what the diesel fuel injection equipment makers ask for in their joint fuel-quality position statement, the same limit Europe’s EN 590 diesel spec uses. They expect fuel above 460 to shorten the life of mechanical parts.
Most ULSD only meets 520 because a lubricity additive was blended in before it reached the station, so pump fuel can be anywhere up to 520 and still be legal, and you cannot tell which from the nozzle. An aftermarket lubricity additive is cheap margin on top. It matters most on everything the fuel itself lubricates: CP3 and CP4 high-pressure pumps, VP44 and Stanadyne DB2/DB4 rotary pumps, and every injector.
What a Good Additive Actually Does
Not all additive claims are equal. Here’s what matters and what’s marketing:
Lubricity improvement, this is the big one. Replacing the lubricity that the low-sulfur refining process strips out of diesel fuel. This directly protects injection pump internals, injector needle valves, and high-pressure pump components from accelerated wear. If an additive does nothing else, lubricity improvement alone justifies its use.
Cetane boost. Higher cetane means shorter ignition delay, the fuel fires faster after injection. This produces smoother combustion, less knock, easier cold starting, and slightly better fuel economy. Most pump diesel is 40-42 cetane; premium diesel is 45-48. A good additive can add 3-5 cetane numbers.
Detergency/deposit cleanup. Detergent additives dissolve varnish and carbon deposits on injector nozzle tips and in injection pump passages. Clean injectors atomize fuel better, which means more complete combustion, less smoke, and better efficiency.
Water separation. Small amounts of water in diesel fuel are inevitable (condensation in tanks, handling, storage). A good additive with a demulsifier makes trace water drop out of the fuel so the water separator can catch it and you can drain it, instead of letting it reach your injectors, where it causes corrosion and erosion at 25,000 PSI.
Cold weather protection. Anti-gel additives keep wax crystals small so they do not clog fuel filters in cold weather. Essential in northern climates, less relevant in California, but worth having if you operate nationally or in the mountains.
Fuel stabilizer. Prevents oxidation and degradation during storage. Important for seasonal equipment (tractors, generators, boats), less critical for daily-driven trucks.
Water and Diesel Bugs: When You Need a Biocide
What people call “diesel algae” is really bacteria and fungi (yeasts and molds). They need free water to grow, so they live where the fuel meets the water in the bottom of a tank, and they do best in fuel that sits: farm and bulk tanks, standby generators, boats and equipment parked for the season. Left alone, the colony builds slime that plugs filters and acidic byproducts that corrode tanks and fuel system parts (Chevron’s Diesel Fuels Technical Review covers the biology).
Signs you have it: filters plugging well before their normal interval, a slimy film on the filter or in the water separator bowl, and a bottom sample with a skin or film where the fuel meets the water. A fuel lab or a field test kit will confirm it.
How to fix it: unless the label says biocide, an additive will not kill diesel bugs. Use a biocide that works in both the fuel and the water, such as Biobor JF or Power Service Bio Kleen, at the shock dose on the label. Then get the dead growth out: drain the water, change the filters, and have a badly fouled tank drained and cleaned, because a biocide cannot reach organisms buried deep in a thick mat and dead slime still plugs filters. Water drained from a treated tank contains biocide, so dispose of it properly.
Prevention is water control: drain the water separator and tank bottoms on a schedule, keep fill caps tight so rain cannot get in, and treat fuel that will sit with a maintenance dose of biocide. Our diesel fuel filter guide covers filter and water separator choices.
Best Diesel Fuel Additive at a Glance: Quick Picks by Need
Short on time? Here are our quick picks, matched to what your diesel actually needs. Every product below is one we recommend and break down in full further down the page, so you can jump straight to the best diesel fuel treatment for your situation. When in doubt, Stanadyne Performance Formula is our year-round default, because it was developed by an injection pump manufacturer.
Full write-ups on every pick, including cost per gallon, are below. Local to the Sacramento Valley or shipping injectors in? Call us at 530-668-0818 and we will point you to the right additive for your engine.
The Additives We Recommend (and Why)
#1: Stanadyne Performance Formula
This is what we use, sell, and recommend to every customer who walks through our door. Here’s why:
Stanadyne manufactures injection pumps. They’re not a chemical company that decided to make a fuel additive, they’re the company that makes the Stanadyne DB2, DB4, and DE injection pumps found in millions of diesel engines worldwide. They developed Performance Formula specifically to protect the systems they build. When the company that machines fuel injection components to 0.0001″ tolerances tells you what to put in your fuel, that carries weight.
It was developed by Stanadyne, an injection pump manufacturer. Most other additives on this list come from chemical or petroleum companies.
What it does:
- Lubricity improvement exceeding ASTM D975 requirements
- Cetane boost (typically 3-5 numbers)
- Injector and pump deposit cleanup (detergent package)
- Water demulsification
- Anti-gel protection (the Performance Formula is an all-season product: Stanadyne also offers a separate Winter 1000 formula for extreme cold)
- Corrosion inhibitor
- Fuel stabilizer
What it won’t do: It’s not a miracle product: it won’t fix a mechanically worn injector.
Cost: Approximately $0.04-$0.06 per gallon treated (16 oz bottle treats 60 gallons). Not the cheapest option, but not the most expensive either.
#2: Opti-Lube XPD
Opti-Lube has built a strong following in the diesel truck community, and their XPD (Xtreme Performance & Detergency) formula delivers genuinely good results.
Strengths: A lubricity-focused formula with a strong detergent package. Many users report MPG improvements.
Considerations: Opti-Lube is a chemical company, not an injection system manufacturer. That doesn’t mean the product is bad, it’s clearly good, but the R&D perspective is different. They optimize for test bench numbers; Stanadyne optimizes for what they see when they take pumps apart.
Cost: Approximately $0.05-$0.08 per gallon treated depending on size purchased. Competitive with Stanadyne.
Best for: Truck owners who want maximum lubricity and MPG improvement and prefer buying from an additive-focused company.
#3: Hot Shot’s Secret Diesel Extreme
Hot Shot’s Secret has earned credibility in the diesel performance and fleet world. Their Diesel Extreme is a concentrated cleaner/additive hybrid.
Strengths: Aggressive detergent package, this is one of the strongest deposit cleaners on the market. If you’re taking over a truck with unknown maintenance history or suspect significant injector deposits, Diesel Extreme is a good “reset” treatment. Also provides solid lubricity improvement and cetane boost.
Considerations: The aggressive cleaning action means it can loosen deposits that then need to be caught by the fuel filter. On a very dirty system, you might need to change the fuel filter after the first treatment. That’s actually a sign it’s working, but be prepared for it.
Cost: Approximately $0.08-$0.12 per gallon treated. More expensive than Stanadyne or Opti-Lube for regular use, but excellent as a periodic deep-clean treatment.
Best for: Periodic deep cleaning (Hot Shot’s says every 6,000 miles), fleet maintenance programs, engines with suspected deposit issues.
#4: Power Service Diesel Kleen + Cetane Boost
Power Service is probably the most widely available diesel additive, you can find the silver bottle at virtually any truck stop, auto parts store, or Walmart. That availability is its biggest strength.
Strengths: Widely available, affordable, decent cetane boost. The winter formula (white bottle: Diesel Fuel Supplement + Cetane Boost) is one of the most popular anti-gel products on the market and works well for cold weather protection.
Considerations: Lubricity improvement is adequate but not class-leading. It’s a solid “better than nothing” additive.
Cost: Approximately $0.03-$0.05 per gallon treated. The cheapest option on this list.
Best for: Budget-conscious users, winter anti-gel (the white bottle), and cases where availability matters more than maximum performance.
#5: Howes Lubricator Diesel Treat
Howes has been around since 1920 and has a loyal following, particularly among long-haul truckers and fleet operators.
Strengths: Good all-around additive with solid anti-gel performance. Alcohol-free formula (some competitors use alcohol-based solvents that can affect certain seal materials). Strong cold weather reputation.
Considerations: Doesn’t contain a cetane improver in the standard formula, if cetane boost is important to you, you’ll need a different product or a supplemental cetane booster.
Cost: Approximately $0.04-$0.06 per gallon treated. Competitive pricing.
Best for: Cold climate operations, users who prefer alcohol-free formulations, long-haul trucking.
Winter Diesel Treatment: Anti-Gel Picks and When to Add Them
Anti-gel has to be in the fuel before the fuel gets cold. Cold-flow additives work by changing how wax crystals form, so they must be blended in while the fuel is still above its cloud point, the temperature where wax first shows (Chevron’s Diesel Fuels Technical Review). Pour it in after the fuel has clouded or gelled and it will not undo the wax that is already there.
When to Add It
- Before the first cold night, not after it. Start when overnight lows head toward freezing where the truck or machine will sit, not where you bought the fuel. Power Service says to switch to its winter formula below 30°F; Hot Shot’s says to use its anti-gel below 32°F.
- Add it, then fuel. Pour the anti-gel in first and let the incoming fuel mix it. Hot Shot’s directions say exactly that.
- Every tank while it is cold. Untreated fuel dilutes what is already in the tank, so treat each fill until the season is over.
- Treat parked equipment before it parks. A tractor, generator or truck that sits through winter needs the anti-gel mixed in while the fuel is warm, then enough run time to pull treated fuel through the filters.
- Drain the water separator before a cold snap. Water that freezes on a filter stops the engine the same way gel does.
- Heading up the hill? If you fuel in the valley and park overnight in Truckee, Tahoe or Reno, treat the tank before you leave.
Anti-Gel Picks
What About 2-Stroke Oil and ATF in Diesel Fuel?
You’ll see this discussed in every diesel forum, adding a small amount of 2-stroke outboard oil (TCW-3 rated) or automatic transmission fluid (ATF) to diesel fuel for lubricity. Here’s our take:
2-stroke oil at 1-2 oz per 5 gallons does add lubricity. There’s legitimate chemistry behind it: TCW-3 oils contain ashless detergents and anti-wear compounds that supplement ULSD. Many fleet operators and long-time diesel owners swear by it. It’s cheap, but check your owner’s manual first, since some engine makers say not to add oil to diesel fuel. However, it doesn’t provide cetane boost, anti-gel protection, or the comprehensive additive package you get from a purpose-built diesel fuel additive. Think of it as a lubricity supplement, not a complete fuel treatment.
ATF is more controversial. It does contain detergents and friction modifiers, and some people report cleaner-running engines. But ATF isn’t formulated for combustion, it’s designed for hydraulic systems and clutch packs. The detergent composition isn’t optimized for injection system deposits, and at higher concentrations it can affect fuel system seals. We don’t recommend it when proper diesel additives are readily available.
Check the Engine Maker’s Guidance First
Your engine maker’s manual decides what is allowed in your fuel. Here is what two makers’ documents say. Each one applies to its own engines and its own manual revision, so treat these as examples, not rules for your engine.
- Properly formulated diesel fuel normally needs no aftermarket additive.
- A recommended cetane improver is allowed when low cetane fuel is suspected.
- Ford’s recommended anti-gel treatment is allowed for fuel gelling.
- Alcohol-based fuel additives are not to be used.
Source: Ford diesel supplement, printed p. 17. Check the manual for your own truck, model year and engine.
Cummins. Two Cummins documents say different things, because they cover different scopes. The RV maintenance presentation says fuel additives are not required, apart from particular cold weather and microbial contamination situations (Cummins RV presentation, PDF p. 21). Separately, on May 10, 2017, Cummins announced that it recommends two Power Service products (Cummins news release).
The takeaway: read your own manual for your engine and model year before you buy anything, and follow it over any general advice, including ours.
How to Choose: What Matters for YOUR Engine
The “best” additive depends on your situation:
Modern common rail truck (Cummins, Duramax, Powerstroke): Lubricity is your top priority. Your injectors and high-pressure pump operate at extreme pressures where fuel lubricity directly impacts service life. Stanadyne Performance Formula or Opti-Lube XPD are the strongest choices. Use every tank, consistency matters more than occasional use. It is a cheap way to help protect against injector problems and CP4 pump failures.
Older mechanical diesel (12-valve Cummins, 7.3 IDI, pre-common-rail): These engines are more tolerant of fuel quality variations, but they still benefit from lubricity and detergency. The VP44 injection pump in particular is sensitive to fuel quality. Stanadyne is especially relevant here since they manufactured many of the injection pumps in these older engines.
Agricultural equipment (tractors, combines, skid steers): Equipment that sits between seasons, runs in dusty conditions, and often gets fuel from on-farm tanks with variable quality needs a comprehensive additive. Lubricity, stabilizer, water separation, and detergency all matter. Stanadyne Performance Formula is the standard recommendation for tractor injection pump longevity, it’s what we tell every farmer who brings a pump in for rebuild. The money spent on additive is a fraction of a Stanadyne pump rebuild.
Cold climate operation: Anti-gel is non-negotiable. Stanadyne Performance Formula provides moderate anti-gel protection; for extreme cold (below 0°F), supplement with Stanadyne Winter 1000 or Power Service white bottle. Howes is also excellent for cold weather.
Fleet operations: Consistency and cost-per-gallon matter at scale. Stanadyne offers bulk pricing (5-gallon jugs and drums). Hot Shot’s Secret Diesel Extreme works well as a periodic deep-clean treatment (Hot Shot’s says every 6,000 miles) combined with a daily-use additive like Stanadyne or Opti-Lube.
How Much Does Fuel Additive Cost vs. What It Saves?
Let’s do the math on a typical diesel truck running 15,000 miles per year at 18 MPG:
You’re spending $40-$50 per year to protect $5,000-$10,000+ worth of fuel injection components. That’s not marketing, that’s basic math.
For agricultural equipment, the calculus is even more favorable. A tractor injection pump rebuild typically ranges from $800–$1,400 for labor alone, with total rebuild costs ranging from $800–$2,800+ depending on pump type and parts. A year’s worth of Stanadyne additive for a farm tractor costs $15-$25. That’s a no-brainer.
Additives to Avoid
We won’t name specific brands, but avoid any diesel additive that:
Claims to “fix” mechanical problems. No additive will repair a worn injector nozzle, a scored pump plunger, or a failed solenoid. If your engine has a mechanical fuel system problem, it needs mechanical repair, not a bottle of miracle fluid. Additives prevent wear; they don’t reverse it.
Contains alcohol as a primary ingredient. Some cheap “fuel treatments” are mostly isopropyl alcohol with a small amount of detergent. Alcohol can affect seals in older fuel systems and doesn’t provide the lubricity improvement that modern diesel engines need.
Makes MPG claims over 10%. Claims of 10-20% improvement are not credible. If your fuel economy improved that much after using an additive, you had a significant deposit problem that was already costing you, the additive fixed an existing issue, it didn’t create magical efficiency.
Has no independent test data. Reputable additive manufacturers publish or reference independent lubricity testing (HFRR/BOCLE), cetane testing (ASTM D613), and other standardized test results. If a brand can’t point to third-party testing, be skeptical.
How We Use Additives at VFI
When we rebuild an injection pump or return a set of tested injectors to a customer, we recommend Stanadyne Performance Formula with every single order. Not as an upsell, as preventive maintenance advice from people who see what happens when injection systems aren’t protected.
We stock Stanadyne Performance Formula, Stanadyne Lubricity Formula, and Stanadyne Winter 1000 at our Woodland, California shop. If you’re local, stop by and pick some up. If you’re a mail-in customer who just had injectors tested or a pump rebuilt, add it to your maintenance routine, the cost is trivial compared to the work we just did on your fuel system.
Stanadyne vs Power Service: Our Head-to-Head
Both Stanadyne Performance Formula and Power Service Diesel Kleen earn a spot on our recommended list above, and customers constantly ask which one wins in a direct comparison. The honest answer is that they are built for slightly different priorities. Here is how they stack up on the factors that actually matter for your injection system.
For most diesel owners who want one additive that protects the injection system year-round, we reach for Stanadyne Performance Formula because its lubricity package was developed by an injection pump maker. If your priority is maximum injector cleaning and cetane, Power Service Diesel Kleen is an excellent call.
For hard winters, Power Service makes a separate anti-gel (the white bottle). Plenty of owners run Stanadyne for routine protection and keep a bottle of Power Service Diesel 911 on hand for cold emergencies. For a deeper look at the additive we reach for most, read our full Stanadyne Performance Formula review.
The Best Additive for CP4 Trucks: Why Lubricity Is Everything
If you run a CP4-equipped truck (2011 to 2016 LML Duramax, 2011 and later 6.7 Powerstroke, or 2019 to 2020 Ram 6.7 Cummins), additive choice is not a maintenance footnote, it is part of protecting the pump. The Bosch CP4 high-pressure pump uses a roller-and-cam mechanism with extremely tight tolerances that depends entirely on the fuel itself for lubrication. When that fuel film breaks down, the pump can fail catastrophically and send metal debris through the entire fuel system, a repair that typically runs $10,000 to $18,000 at a California specialty shop.
That is why lubricity matters more than any other additive property on these trucks. The refining that makes ultra-low sulfur diesel stripped out much of the natural lubricity older fuel provided, and a lubricity additive restores the protective film the CP4 was never really designed to live without. Not every additive does this: injector cleaners are detergents, not lubricants, and cetane boosters improve combustion, not lubricity. You want an additive with a documented lubricity package.
Frequently Asked Questions
What is the best diesel fuel additive for common rail engines?
For common rail diesel engines (Cummins 6.7L, Duramax, Powerstroke 6.7L), we recommend Stanadyne Performance Formula as the best all-around diesel fuel additive. It provides the lubricity improvement that high-pressure common rail systems need, along with cetane boost, detergency, and water separation. Opti-Lube XPD is a strong alternative with a lubricity-focused formula. The key is consistency, use a quality additive every fill-up, not occasionally.
Is Stanadyne Performance Formula worth the cost?
At approximately $40-$50 per year for a typical diesel truck, Stanadyne Performance Formula costs a fraction of the fuel injection components it protects. A single common rail injector costs $300–$550 (reman) to $500–$900 (new OEM); a high-pressure pump runs $1,200–$2,000+ for a CP3 or $3,500–$6,000+ for a CP4. It was developed by Stanadyne, an injection pump manufacturer, specifically to protect injection system internals. From our perspective as an authorized Stanadyne dealer who sees inside these systems daily, it’s one of the cheapest insurance policies available for a diesel engine.
Can I use 2-stroke oil instead of diesel fuel additive?
Some owners add TCW-3 2-stroke oil for lubricity, but it is not a purpose-built diesel additive. Check your owner’s manual first, since some engine makers say not to add oil to diesel fuel. It doesn’t provide cetane boost, anti-gel protection, water separation, or deposit cleaning: it’s a lubricity supplement only. A purpose-built diesel fuel additive provides a more comprehensive package. Some diesel owners use both: a quality additive for the complete treatment plus a small amount of 2-stroke oil for extra lubricity insurance.
How often should I use diesel fuel additive?
Every fill-up. Consistency is more important than concentration. Using a quality additive every tank provides continuous protection to your injection system. Occasional use is better than nothing, but you lose the cumulative benefit of consistent detergency and lubricity. For deep cleaning treatments like Hot Shot’s Diesel Extreme, Hot Shot’s says to use 16 oz per 40 gallons every 6,000 miles, in addition to your regular daily-use additive.
Do diesel fuel additives actually improve fuel economy?
Cetane improvement (more complete combustion) and deposit cleanup (better injector spray patterns) can help fuel economy. Trucks with significant existing deposits may see the most change as the additive cleans the system. Claims of 10%+ improvement are not credible for a healthy engine.
What diesel fuel additive is best for tractors and farm equipment?
Stanadyne Performance Formula is the standard recommendation for agricultural diesel equipment. Farm tractors face unique fuel quality challenges, on-farm fuel storage tanks, seasonal use with long storage periods, and dusty operating conditions. Stanadyne provides lubricity, stabilization, water separation, and detergency in one product. It’s particularly important for equipment with Stanadyne injection pumps (common in John Deere, Case IH, and Ford tractors), but benefits all diesel injection systems. The cost is $15-$25 per year for a typical farm tractor, trivial compared to an $800–$2,800+ injection pump rebuild.
Does Valley Fuel Injection sell Stanadyne fuel additives?
Yes. As an authorized Stanadyne dealer, we stock Stanadyne Performance Formula, Stanadyne Lubricity Formula, and Stanadyne Winter 1000 at our Woodland, California shop. We also recommend Stanadyne additives to every customer who has injectors tested or injection pumps rebuilt through our mail-in service. Call 530-668-0818 for pricing and availability.
Protect Your Diesel Injection System
Valley Fuel Injection & Turbo is an authorized dealer for Stanadyne, Bosch, Delphi, Denso, and Yanmar. We sell Stanadyne fuel additives and provide professional injector testing, injection pump rebuilds, and complete fuel system service.
📞 (530) 668-0818
📍 1243 E Beamer St, Suite C, Woodland, CA 95776
🕐 Monday–Thursday 7:00 AM – 4:30 PM · Friday 7:00 AM – 4:00 PM
Serving: Woodland · Sacramento · Davis · Vacaville · Yuba City · Stockton · Chico · Redding · Nationwide mail-in service




1 Comment
What’s best precautions to take on a 2005 LLY don’t notice any smoke at start up seems to run and start fine has had Howes used by previous owner
Currently 135,000 miles
Should I clean with hot shot diesel extreme and then what additive do u recommend regularly